How To Make A Temporary Door

How To: DIY a Space-Saving Sliding Door

Calculation a sliding door between rooms can be easier than you lot call up! Follow this photograph tutorial for how to build yours from scratch and you'll take a piddling more privacy—and a little more style—in just a weekend.

Photo: Ohoh Blog for Bob Vila

When you take a doorway but not enough room for a door to swing open, oftentimes the frame goes without whatsoever sort of roofing—or, worse, a temporary curtain divider that hangs there for anot-so-temporary corporeality of time. Fortunately, homeowners hoping for a little more privacy or a fashion to hide a closet'southward contents have a amend workaround that nonetheless involves a drape rod: mounting a slim sliding door. This sort of installation easily distinguishes living areas while also providing a modern, even industrial, impact. Check out this trouble-solving tutorial—adjustable to all doorway sizes—that will get out you with the separated spaces that yous crave.

Photograph: Ohoh Weblog for Bob Vila

MATERIALS AND TOOLS Available on Amazon
– 2×2 lumber, viii feet long (iv)
– Measuring tape
– Pencil
– Manus saw
– Metal corner braces (xviii)
– 11⁄2inch screws
– 2inch rubber rigid casters (2)
– 5mm plywood board (2)
– Drill
– Jigsaw
– Woods glue
– Handles (2)
– Palm sander
– Paintbrush
– Woods stain
– Wood varnish
– Hitch rings (2)
– Wallmounted pall rod

Pace ane

Photo: Ohoh Blog for Bob Vila

Y'all offset need to build the DIY sliding door frame using 2×2 lumber. Dimensions for your build volition largely be dependent on the size of your doorway, then that the sliding door is big enough to cover the entryway and then some. We added 2 inches to the width and the acme of the doorway dimensions to make up one's mind what size to make our door.

Cut the ii×two wooden pieces into the basic that will brand up your frame: two vertical posts that are ii inches taller than the doorway's pinnacle and five horizontal crosspieces, each 1 inch shorter than the width of the doorway. (When yous add the 1-1⁄2-inch thickness of a vertical post on each side, you lot'll observe that the frame is indeed 2 inches wider than your doorway.)

Lay the pieces out equally pictured above, placing one crosspiece at the pinnacle, another 1 1⁄2 inches from the bottom, and the other three spaced so that they are equidistant (likely about xx inches apart).

Stride 2

Photo: Ohoh Blog for Bob Vila

Assemble all the wooden pieces together using 1-1⁄4-inch metallic corner braces. Screw a brace in each corner of the frame—four in each rectangle and two more at the very bottom—in club to brand your construction extra sturdy.

Double-cheque the measurements on the bottom crosspiece before screwing information technology in identify: It must be ane-1⁄2 inches from the bottom of either vertical post and then that you can set the casters inside the frame and afterwards hide them behind the plywood board.

STEP 3

Photograph: Ohoh Blog for Bob Vila

Screw the 2-inch rubber casters on the bottom crosspiece, i simply inside the corner brace on each side.

STEP iv

Photo: Ohoh Blog for Bob Vila

You must strengthen the framework right where the door pull volition become, because this side will get a lot of tugging to open up and close your wheeled door. Measure the distance between the 2d and third crosspieces from the bottom, and cut this length from your remaining two×2 lumber.

Position this freshly cut vertical piece in the second rectangle from the lesser, where you lot simply measured, leaving plenty room from the outer edge to fit the metal door pull. Screw through the horizontal pieces to hold it in identify, and then your framework is complete!

Footstep 5

Photograph: Ohoh Weblog for Bob Vila

Cut your two sheets of plywood (normally bachelor in iv anxiety wide by 8 anxiety long) into the exact dimensions of the wood frame, which will besides be the dimensions of your DIY sliding door. One will cover the front of the frame, and the other the back. Virtually big-box hardware stores will brand the cuts for you right at the time of purchase!

Identify i lath on the wooden frame and mark the pull's location with a pencil.

STEP six

Photo: Ohoh Blog for Bob Vila

Utilize a drill and a jigsaw to cut out a pigsty to fit the recessed door pull. Then line up your ii plywood boards, trace the hole, and cut out a hole on the second board for the other door pull.

Step seven

Photograph: Ohoh Weblog for Bob Vila

Next, glue one of the plywood lathdue south onto the frame. Cover each 2×ii with wood glue, hover the plywood over it to meet that the side with the door pull's hole lines up with the side of frame that is reinforced, then lower and clench. Get out the clamps in place for every bit long as the glue specifies that information technology needs to cure.

After the glue dries completely, turn the DIY sliding door over and do the aforementioned for the other side.

STEP 8

Photo: Ohoh Weblog for Bob Vila

Remove the clamps once all of the gum has dried and check if the plywood boards accept adhered to the wood frame. You should run into that the casters are now completely embedded in the door, partially covered by the plywood lath.

Pace 9

Photo: Ohoh Weblog for Bob Vila

Accept a palm-sander to completely smooth the DIY sliding door, particularly the edges.

Stride 10

Photo: Ohoh Web log for Bob Vila

Time to give the DIY sliding door its finished look! We've stained ours with a nighttime chocolate shade, but yous can cull any stain color (or, alternatively, pigment!) to complement your space'south scheme. Subsequently the stain dries, follow with a coat of varnish.

Pace 11

Photo: Ohoh Blog for Bob Vila

Fit the door pull into the spaced carved for it, adhering with woods glue.

Step 12

Photograph: Ohoh Blog for Bob Vila

Screw the hitch rings on the top of the door, one an inch from each terminate.

Step 13

Photo: Ohoh Web log for Bob Vila

Finally, stand your door and prepare to slide information technology into position. You'll desire to inquire a partner for assistance property the DIY sliding door while you put information technology on its "runway"—a wall-mounted drape rod. Hither, our mantle rod spans wall to wall. But if that's not the instance with your kit, pick up a couple of curtain rod brackets to fix it to the one wall with the doorway.

First, slide the curtain rod through the door's rings, then button the door toward the wall and then that its close enough for the curtain rod to mount just with enough room for the door to wheel dorsum and forth. The DIY sliding door should be standing direct (not leaning), with full weight resting on the casters rather than pulling on the rod—that'south but there to guide the door. Now, check that the rod is perfectly horizontal and marking where it meets the wall. (This is where a partner comes in handy!) Spiral the rod to the wall, and this project is an open up-and-shut instance.

Photo: Ohoh Web log for Bob Vila

Ama is a DIY addict and the creative heed backside Ohoh Blog. She likes home decor, lighting, and piece of furniture projects that may involve painting, sewing, drilling…no thing the technique! Whatever she has on hand is inspiration to create, and fodder for her serious addiction to upcycling.

Source: https://www.bobvila.com/articles/diy-sliding-door/

Share this post